Home :: HVA Factory UK Parts

HVA Factory UK Parts

Products

Sign in to rate
1972-2002 Husqvarna 125 250 360 390 400 430 500 510 Extended Alloy Shift Lever
SKU: HVA-GEARLEVER
HVA Factory UK Gear Lever - Longer version

1970s to 2002

Husqvarna Extended 140mm centre to centre Folding Tip Gear Lever, NEW Longer version to best suit HVA Factory Footrests!. Made from Forged Alloy - stronger than our previous versions.

Fits all 2t from 1982 to 1988 plus earlier models and 4t from 1983 to 2002

Also fit 2 peice 4t Clutch cover.

Plus earlier bikes with the same spline...

$35.95
Qty
Add to wish list
Sign in to rate
1975-1981 Husqvarna 125 250 360 390 Billet Alloy Clutch Basket Cush Drive
SKU: HVA-1975CLBASKET
Husqvarna Clutch Basket Early Cush Drive Type 161114901 / 16-11-149-01

Husky 5 spring cush drive basket

Will fit various years and models. Double check your basket before ordering.

$149.95
Qty
Add to wish list
Sign in to rate
1975-1984 Husqvarna 125 250 360 390 430 Clutch Fiber & Steel Plates for the 5 spring clutch
SKU: HVA-CLUTCHPLATES
Husqvarna 16-11-157-01 & 16-11-158-01

High quality clutch kit for all huskys with 5 springs clutches from 1975-1984. 6 x Fiber Plates and 5 x plain Steel Discs. TOTAL Stack Height is 28.5mm

For bikes using the clutch hub 16-11-156-01

Note some late 1984 and onward bikes with the hub 16-15-088-01 use a higher stack.

$104.95
Qty
Add to wish list
Sign in to rate
1975-1984 Husqvarna Oversize Foot Pegs & Mounting Kit
SKU: HVA-1019
Fit almost all bikes from 1966-1984..not 72-74 but 1975 with slight mod.

New oversize stainless steel foot pegs. Never have your feet slip off the pegs again! The best pegs on the market today for vintage Husqvarna motorcycles.

Custom made for HVA-FACTORY, these footrests are cast from Stainless Steel and polished. They use the standard spring. A fitting kit (shown) with the correct bolts / spacers / washers and a pair of springs is also included.

I have been told these pegs are a direct bolt on for the 74-82 Can Am models as well.

$134.95
Qty
Add to wish list
Sign in to rate
1979-1989 Husqvarna Steering Head Bearing Set 151307001 / 15-13-070-01
SKU: 15-13-070-01
Husqvarna Steering Head Bearing Set 151307001 / 15-13-070-01

Complete set of two complete bearings and seals.

From 1979 to 1989



$34.00
Qty
Add to wish list
Sign in to rate
1981-1984 Husqvarna Swing Arm Bushing, Bearing & Seal Kit Twinshock Bikes
SKU: HVA1024
Husqvarna Swing Arm Bushing, Bearing & Seal Kit Twinshock Bikes

Husqvarna 15-10-621-01 15-10-778-01 740481004 15-10-607-01 HVA1024

Complete bush, bearing and seal kit for husqvarnas from 1981-1984 + some earlier - please check.


$65.00
Qty
Add to wish list
Sign in to rate
1982 1983 1984 Husqvarna 250 430 500 5 Clutch Spring Set Medium
SKU: HVA-CLSPRINGS
1982 1983 1984 Husqvarna 250 430 500 5 Clutch Spring Set Medium

A quantity of 1 gets you 5 springs.



$20.95
Qty
Add to wish list
Sign in to rate
1982 1983 1984 Husqvarna 250 430 500 Billet Alloy Clutch Basket 5 Spring
SKU: HVA-1982CLBASKET
Husqvarna Clutch Basket 161120301 / 16-11-203-01

Husky clutch basket 82 - 84 5 spring

All 240/250/430/500 bikes with the 5 spring clutch...

Made exclusively for HVA Factory by Talon.
$134.95
Qty
Add to wish list
Sign in to rate
1982-1984 Husqvarna CR WR XC Air Cooled Clutch Cover
SKU: HSQ-CLCOVER
This is a sand cast part made in the UK. The finish is not perfect but it will look very nice painted black. They replace part number: 611644 V1

I know that they fit most capacities also I am told the 510 four stroke - you need to check!

The new cast and CNC machined cover is made from a strong, weldable grade of Aluminium and is flat - to seat perfectly on to the engine casing using a small bead of silicone sealant.

They do not come with any other parts, so you will need your old one for attached parts (dowells etc)

They are cast from high quality Aluminium - not the Magnesium that they were made from - this means that if you should break it (unlikely as it is a little thicker), that most welders will be able to repair it.

This cover will work on all 82-84 model air-cooled Husky's. It will probably fit the 1981 CR 430 as well. Please check with your local husky dealer before purchasing.

Special order. 2-3 weeks for delivery.
$349.95
Qty
Add to wish list
Sign in to rate
1982-1988 Husqvarna CR WR XC Ignition Cover
SKU: HSQ-IGNCOVER
This is a sand cast part made in the UK. The finish is not perfect but it will look very nice painted black. The reason for this is that the plastic cover distorts, letting in the water if over tightened - potentially giving you ignition problems.

The new cast and CNC machined cover is made from a strong, weldable grade of Aluminium and is flat - to seat perfectly on to the engine casing using a small bead of silicone sealant.

This cover will work on all 83/84 model Husky's. It will probably fit the 1982 and 85-88 models as well. Please check with your local husky dealer before purchasing.
$84.95
Qty
Add to wish list