FENDER MOUNTING HARDWARE KIT FOR PLASTIC FRONT FENDER
(32 pieces) to secure the stock plastic front fender on many early Yamaha dirt bikes. These parts are faithful reproductions of the originals.
You get all items pictured to attach a high mounted a plastic front fender to either cast iron or aluminum triple clamps:
- 4 bolts M6-1.0 X 30mm long for use with aluminum triple clamps (97323-06030-00)
- 4 bolts M6-1.0 X 25mm long for use with cast iron triple clamps (97323-06025-00)
- 4 flat washers (90201-06067-00)
- 4 lock washers (92995-06100-00)
- 4 collar washers (90387-06388-00)
- 8 rubber grommets (322-21541-00-00)
This setup was used to attach the high plastic front fenders on many bikes including:
YZ80 A, B, C
YZ125 A, B, C
YZ250 A, B, C
YZ360 A, B
YZ400 C
MX100 A, B
MX125 A, B, C
MX175 A, B
MX250 A, B
MX400 B
DT2MX
RT2MX
SC500 A
TT500 C, D, F, G, H
DT100 A, B, C
DT125 A, B, C
DT175 A, B, C
DT250 A, B, C
YZ 125 250 400 77-79
YZ 100 76-79
These are a universal fitment. May work on other models as well. They were originally offered by Maier.
Will work on any drum brake and cable clutch vintage mx or enduro machine. You will have to drill your own holes. They bolt on using the stock perch bolt that goes through the lever. You can either zip tie the remaining part of the guard to the cable or use a small nut and bolt to hold it securely in place.
Available in many colors!
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers.
These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
Fits the 10" wheel models.
Fits the 10" wheel models.
3/4" OD
1/2" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/4" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/8" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
Steel Zinc Plated Flanged Bushing Washer for Motorcycle Plastic 21mm OD x 3.5mm deep x 6.4mm ID
Protect your lower fork legs. Click on the item to select a color.