- per page
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers.
These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
M6x1.0x30mm (10)
M6x1.0x25mm (10)
M6x1.0x20mm (10)
M6x1.0x16mm (10)
M6x1.0 Flange Locking Nut (10)
M6x16mm Fender Washer (10)
You may need more of less of a certain size depending on your bike. Liquid cooled bikes typically use more bolts.
New DC Plastics injection molded universal oval number plate unit. No more rivets or bolts showing through your front number plate. This oval has the mounting brackets molded unto the backside of the front number plate. They are not seen from the front. This plate zip ties on with 4 zip ties. Easy installation for the best front number plate on the market today. These plates measure 9.25" x 11". The have a molded lip all the way around just like our vacuum formed ovals. We have more colors on the way. They are perfect quality with a gloss finish. 6.5" spacing for 1974 and older 250's 7.5" spacing for 1975 and newer 250's. Some of the 125's had smaller spacing. Measure the distance from the center of one fork tube to the center of the other before ordering. The molded mounting brackets will work with fork tubes from 30 to 43mm in diameter.
Fresh batch as of December 2019. We had to increase the price due to material costs.
Available in all of our colors.
Universal Hodaka Model 94 & 95 Front Fender Combat Wombat
Available in gray (shown), light gray, white, translucent, orange and black.
Also works on any bike that uses a front fender brace for mounting with no flat top mount.
Tip to tip straight across it measures 24 inches. Tip to tip around the curve measures 29 inches.
Universal Hodaka Model 94 & 95 Rear Fender Combat Wombat
Available in gray (shown), light gray, white, translucent, orange and black.
5 inches wide.
These are a universal fitment. May work on other models as well. They were originally offered by Maier.
Fits the 10" wheel models.
Fits the 10" wheel models.
Will work on any drum brake and cable clutch vintage mx or enduro machine. You will have to drill your own holes. They bolt on using the stock perch bolt that goes through the lever. You can either zip tie the remaining part of the guard to the cable or use a small nut and bolt to hold it securely in place.
Available in many colors!
3/4" OD
1/4" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/8" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/2" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
- per page
