FENDER MOUNTING HARDWARE KIT FOR PLASTIC FRONT FENDER
(32 pieces) to secure the stock plastic front fender on many early Yamaha dirt bikes. These parts are faithful reproductions of the originals.
You get all items pictured to attach a high mounted a plastic front fender to either cast iron or aluminum triple clamps:
- 4 bolts M6-1.0 X 30mm long for use with aluminum triple clamps (97323-06030-00)
- 4 bolts M6-1.0 X 25mm long for use with cast iron triple clamps (97323-06025-00)
- 4 flat washers (90201-06067-00)
- 4 lock washers (92995-06100-00)
- 4 collar washers (90387-06388-00)
- 8 rubber grommets (322-21541-00-00)
This setup was used to attach the high plastic front fenders on many bikes including:
YZ80 A, B, C
YZ125 A, B, C
YZ250 A, B, C
YZ360 A, B
YZ400 C
MX100 A, B
MX125 A, B, C
MX175 A, B
MX250 A, B
MX400 B
DT2MX
RT2MX
SC500 A
TT500 C, D, F, G, H
DT100 A, B, C
DT125 A, B, C
DT175 A, B, C
DT250 A, B, C
YZ 125 250 400 77-79
YZ 100 76-79
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers.
These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
3/4" OD
1/2" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/4" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/8" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
Steel Zinc Plated Flanged Bushing Washer for Motorcycle Plastic 21mm OD x 3.5mm deep x 6.4mm ID
M6x1.0x30mm (10)
M6x1.0x25mm (10)
M6x1.0x20mm (10)
M6x1.0x16mm (10)
M6x1.0 Flange Locking Nut (10)
M6x16mm Fender Washer (10)
You may need more of less of a certain size depending on your bike. Liquid cooled bikes typically use more bolts.
