- per page
1971-1975 Suzuki TM 100-400 Inner Rear Fender
Will fit the following models:
1973-1975 Suzuki TM 100/125
1972-1975 Suzuki TM 250
1971-1975 Suzuki TM 400
Available in yellow or black.
FENDER MOUNTING HARDWARE KIT FOR PLASTIC FRONT FENDER
(32 pieces) to secure the stock plastic front fender on many early Yamaha dirt bikes. These parts are faithful reproductions of the originals.
You get all items pictured to attach a high mounted a plastic front fender to either cast iron or aluminum triple clamps:
- 4 bolts M6-1.0 X 30mm long for use with aluminum triple clamps (97323-06030-00)
- 4 bolts M6-1.0 X 25mm long for use with cast iron triple clamps (97323-06025-00)
- 4 flat washers (90201-06067-00)
- 4 lock washers (92995-06100-00)
- 4 collar washers (90387-06388-00)
- 8 rubber grommets (322-21541-00-00)
This setup was used to attach the high plastic front fenders on many bikes including:
YZ80 A, B, C
YZ125 A, B, C
YZ250 A, B, C
YZ360 A, B
YZ400 C
MX100 A, B
MX125 A, B, C
MX175 A, B
MX250 A, B
MX400 B
DT2MX
RT2MX
SC500 A
TT500 C, D, F, G, H
DT100 A, B, C
DT125 A, B, C
DT175 A, B, C
DT250 A, B, C
YZ 125 250 400 77-79
YZ 100 76-79
Complete Seat Base and Brackets. No cover or foam. The steel brackets are zinc plated.
Fits the following models:
73-75 TM 100
73-75 TM 125
74-75 TM 250
73-75 TM 400
Available in yellow or translucent. Please click on the item to select a color.
This base includes rear brackets bolted on and a front bracket. Ready to install a foam and cover.
Complete Seat Base and Brackets. No cover or foam. The rear steel brackets are zinc plated. The front bracket is plastic.
Fits the following models:
78/79 PE 175
77-79 PE 250
78/79 PE 400
This unit is ready to bolt on and ride. You will have to trim your stock side panel down to fit, or you can purchase one of our pre-cut panels. Includes the carb boot, complete filter case, new air filter, hose clamps and outer cover bolts. It comes with mounting instructions.
Available in translucent, yellow or black. Also available in no vent, half vent or full vent. Please click on the picture to make your selections.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers.
These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
3/4" OD
1/2" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/4" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/8" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
- per page
