FENDER MOUNTING HARDWARE KIT FOR PLASTIC FRONT FENDER
(32 pieces) to secure the stock plastic front fender on many early Yamaha dirt bikes. These parts are faithful reproductions of the originals.
You get all items pictured to attach a high mounted a plastic front fender to either cast iron or aluminum triple clamps:
- 4 bolts M6-1.0 X 30mm long for use with aluminum triple clamps (97323-06030-00)
- 4 bolts M6-1.0 X 25mm long for use with cast iron triple clamps (97323-06025-00)
- 4 flat washers (90201-06067-00)
- 4 lock washers (92995-06100-00)
- 4 collar washers (90387-06388-00)
- 8 rubber grommets (322-21541-00-00)
This setup was used to attach the high plastic front fenders on many bikes including:
YZ80 A, B, C
YZ125 A, B, C
YZ250 A, B, C
YZ360 A, B
YZ400 C
MX100 A, B
MX125 A, B, C
MX175 A, B
MX250 A, B
MX400 B
DT2MX
RT2MX
SC500 A
TT500 C, D, F, G, H
DT100 A, B, C
DT125 A, B, C
DT175 A, B, C
DT250 A, B, C
YZ 125 250 400 77-79
YZ 100 76-79
1979 1980 Kawasaki KX 125 250 Front Number Plate Unit Green
Injection molded. Installs with four zip ties behind the plate.
1980 Kawasaki KX 80 Front Number Plate Green
This does not have the hole cut for the throttle cable. The plate does include brackets for the back of the plate that you can bolt or rivet onto the plate.
7.5" x 9.5"
Will fit the following models:
1982 KX 125
1983 KX 125, 250 & 500
Available in kx green or translucent.
Measures 13" wide and 13" tall.
The plate measures 13 inches wide where it mounts on the outside of each fork leg. Top to bottom, the plate measures 12 inches. The plastic mesh on the inside measures 9.5 inches x 7.25 inches.
This front plate will probably fit other makes and models. Check your measurements before ordering.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers.
These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
3/4" OD
1/2" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/4" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
3/4" OD
1/8" Thick
Great for getting the perfect spacing for side panels, shrouds, etc. 6mm inside hole works with most bikes. Made from 6061 alloy.
DC Plastics recommends using these flanged washers for mounting all motorcycle plastic where applicable. They will only work with 6mm bolts. 6mm is the typical size for most side panel, number plate, fender, etc bolts. Double check your mounts before ordering. Some models to not have enough room at the bolt hole to fit these washers. These help distribute the weight across the mounting eyelet and do not allow the plastic to be pinched into place. Your plastic should last longer if you use these instead of flat fender washers. Sold individually.
Steel Zinc Plated Flanged Bushing Washer for Motorcycle Plastic 21mm OD x 3.5mm deep x 6.4mm ID
Click on the picture or title to select a color.
New DC Plastics injection molded universal oval number plate unit. No more rivets or bolts showing through your front number plate. This oval has the mounting brackets molded unto the backside of the front number plate. They are not seen from the front. This plate zip ties on with 4 zip ties. Easy installation for the best front number plate on the market today. These plates measure 9.25" x 11". The have a molded lip all the way around just like our vacuum formed ovals. We have more colors on the way. They are perfect quality with a gloss finish. 6.5" spacing for 1974 and older 250's 7.5" spacing for 1975 and newer 250's. Some of the 125's had smaller spacing. Measure the distance from the center of one fork tube to the center of the other before ordering. The molded mounting brackets will work with fork tubes from 30 to 43mm in diameter.
M6x1.0x30mm (10)
M6x1.0x25mm (10)
M6x1.0x20mm (10)
M6x1.0x16mm (10)
M6x1.0 Flange Locking Nut (10)
M6x16mm Fender Washer (10)
You may need more of less of a certain size depending on your bike. Liquid cooled bikes typically use more bolts.
